Home > Inline Skates > Speed Skates >

  Vanilla Spyder Speed Skates - 2014
Vanilla Spyder Speed Skates - 2014
Vanilla Spyder Speed Skates - 2014

List Price: $399.00
Our Price: $379.00
You save $20.00!
You'll earn 191 points

Availability: Ships in 24 to 48 hours
Product Code: VILSPY



Description Sizing Info
Vanilla Spyder Speed Skates - 2014 - THESE ARE IN MEN'S SIZES! Theses skates are even more beautiful in person then they look on the site! Absolutely breathtaking skates with a performance package for serious racing action. These are the sickest skates we have seen this season!

Vanilla Spyder

Carbon fiber, Ultra light heat moldable boot

lazer cut windowing on this 7000 Series Frame

Four 110mm 85A high rebound indoor/outdoor wheels

Racing spec speed bearings - Vanilla reaction
Vanilla Spyder velocidade Patins - 2014 - ESTES SÃO NOS TAMANHOS DOS HOMENS! Teses patins são ainda mais bonita pessoalmente, então eles olham no site! Patins Absolutamente tirar o fôlego com um pacote de performance para corridas acção séria. Estes são os patins mais doentes que vimos nesta temporada!

Vanilla Spyder

A fibra de carbono, o calor ultra leve bota moldável

lazer cortar janelas neste quadro Series 7000

Quatro 110 milímetros 85A alta rebote rodas interior / exterior
Rolamentos de velocidade especificação Racing - reação Vanilla

Vanilla Skate shoes Heat Molding Instructions

1. Remove wheels and bearings. Leave the frames attached to the boot. The frame should be snug on the boot, but not overly tight. You should be able to move the frame from side to side when you apply pressure with your hands.

2. Turn on oven and set temperature to 175 – 200 degrees Fahrenheit. Do not go beyond 200 degrees at any time for any reason.
3. Heat and mold one boot at a time. Before putting your boot and frame in the oven, be sure to loosen the laces enough to easily slide your foot in the boot.
4. Place the boot and frame in the oven. Make sure not to let the boot or frame make contact with the heating elements.
5. Check the oven after 10 minutes to see if the boot is pliable. If you’re not satisfied with the pliability, check it every minute with a maximum of 10 additional minutes.
6. Remove from oven with caution! Use hot pad or mitt to remove the boot and avoid contact with the frame and eyelets.
7. While sitting in a chair, place the boot on your foot and lace your boots snug – do not over‐tighten. Be sure to wear a sock during this process to protect your foot against the heat. Do not stand on the frame until your boot has completely cooled.
8. While sitting, keep your hip and knee in line. Your knee should be directly over your toes. This is an important position to maintain during the molding process.
9. Once your boot has completely cooled, repeat steps 1‐8 for the other boot/frame.

Additional Molding Tips

a. Most skaters have made great use of a handled screw driver to push out the ankle bone while your boot is hot and pliable. Using the handle to apply pressure can help move the shell out to specific points.
b. If you find that the toe box is tight, use your thumbs to press and hold out the areas in the toe box of your boot while the boot is hot and pliable.
c. To tighten the heel cup and tendon, place your hands around the back of the boot and squeeze the boot together.

Hold the cup/tendon tight until the boot has cooled.

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Inline Skates > Speed Skates
Inline Racing Skates
Inline Skates
Inline Skates > Vanilla Inline Skates